FISHINGFIX
← The Journal
· The FishingFix Team

How to Join Braid to a Leader: Knots, Leader Strength and Length

Braided line casts a long way, holds a lot of line on a small spool and has almost no stretch, so you feel every touch. It also shows up clearly in the water, cuts into itself under load and frays quickly on rock or shell. The usual answer is a leader: a few feet of monofilament or fluorocarbon between the braid and the lure. This guide covers why, which knot to use for the join, and how to choose a leader strength using the figures in our Fishing Knot Guide and Fishing Line Calculator.

Why put a leader on braid

  • Visibility. Braid is opaque and often brightly colored. A clear leader puts something less visible near the lure, which matters most in clear water and with wary fish.
  • Abrasion. Braid's thin fibers fray when dragged over rock, shell, wood or a fish's rough jaw. A thicker monofilament or fluorocarbon leader takes that wear and can be replaced cheaply.
  • Shock. With no stretch, a hard hookset or a sudden lunge loads everything at once. A length of stretchy monofilament softens the blow.
  • A planned weak point. If the leader is lighter than the braid, a snag breaks the leader at the lure, not the braid somewhere up the line. You lose a lure and a few feet of leader, not a long length of expensive line.

For pike and musky the leader has another job: their teeth cut through monofilament and braid alike, so the Bait Selector recommends a wire leader for pike. Wire is joined with a swivel or a crimp rather than a knot.

Three knots for the join

The knot guide lists three knots for joining lines. Their approximate strengths, as a percentage of the line's rating, are:

  • Double Uni Knot, about 90%. Two uni knots, one tied in each line around the other, slid together. It copes well with lines of very different diameters and materials, which is exactly the braid-to-leader case. Tie more turns in the braid (eight to ten) than in the leader (four to six), because slick braid needs more grip.
  • Surgeon's Knot, about 90%. Lay the two lines side by side, tie an overhand knot with both together, pass the whole leader end through a second (or third) time, wet and pull. Fast and easy, but the leader's whole tag passes through the loop, so it suits shorter leaders, and the knot is bulky in the rod guides.
  • Blood Knot, about 85%, rated advanced. Best for two lines of similar diameter, such as joining sections of monofilament. With thin braid against a thicker leader it tends to slip, so it is the least suited of the three here.

There are specialist braid-to-leader knots with their own followings. The double uni is a good place to start because it is the same knot as the uni you already use at the hook.

Tying the double uni, step by step

  1. Overlap the braid and the leader by about a foot, tag ends pointing in opposite directions.
  2. Take the braid's tag end, form a loop back along the two lines, and wrap it around both lines and through the loop eight to ten times. Pull the tag to snug it, but not fully tight.
  3. Do the same with the leader's tag around the braid, four to six turns.
  4. Wet both knots well. Pull the two standing lines apart so the knots slide together and seat against each other.
  5. Pull each tag firmly, then the standing lines again. Trim both tags, leaving a couple of millimeters.
  6. Test with a steady pull, using a glove or a wooden handle rather than wrapping thin braid around a finger.

Choosing the leader's strength

The connection holds only as much as its weakest part. Say you spool 20 lb braid and tie on a 12 lb fluorocarbon leader with a double uni, then attach the lure with a Palomar. On the knot guide's figures:

  • The braid at the double uni keeps about 18 lb of its 20 lb rating.
  • The leader at the double uni keeps about 10.8 lb of its 12 lb rating.
  • The leader at the Palomar keeps about 11.4 lb.

So the weakest point is the leader side of the line-to-line knot, at around 10.8 lb, and that is where a snag will part. Set the drag well under that figure. If you want the break to happen at the lure instead, so the leader stays on, use a terminal knot that keeps less than the join does, or a slightly heavier leader.

As a starting point for the leader itself, the line calculator's recommended pound test for your target species is a reasonable figure: 12 lb for bass and 20 lb for saltwater inshore fishing, for example. Go heavier where abrasion is the main threat (oyster bars, rocky shorelines, heavy timber) and lighter in very clear water for shy fish.

How long a leader?

There is no single right length. Shorter leaders, a couple of feet, keep the knot outside the rod guides when you cast and are quicker to tie. Longer leaders, the length of the rod or more, put more distance between the visible braid and the lure and give more stretch and more abrasion protection, but the join then passes through the guides on every cast, which is where a slim knot such as the double uni earns its place. A leader roughly the length of the rod is a common compromise for spinning gear.

Check the leader often. Run it between your fingers after every fish and every snag; rough or flattened sections mean it is time to cut back or replace it. Retie the line-to-line knot whenever the leader gets short.

Why braid fills a spool so much further

Because braid is so thin for its strength, the same spool holds far more of it. On a medium spinning spool with a 1.85 inch flange and 0.55 inches between the flanges, the Fishing Line Calculator gives 481 yards of a 0.008 inch braid against 213 yards of a 0.012 inch monofilament. Few anglers need that much braid, which is why a mono backing under the braid is common; how much line a reel holds works through the split.

Safety

Strength figures are rough angler numbers, not lab results: a knot's strength varies with the line, how well it is tied and wetted, and who tested it. The line's own rating is the maker's. Test a knot by hand before you trust it, and never use fishing knots or line for climbing, lifting or anything that holds a person.

  • Braid under load is thin enough to cut skin. Never wrap it around fingers or hands to break off a snag; point the rod straight at the snag and walk back, or wrap the line around something solid.
  • Wear sunglasses. A knot or leader that fails under a hard pull sends the lure back toward you.
  • A hook near the eye or deeply embedded in skin needs medical care rather than a roadside fix.
  • When rigging in a boat or kayak, wear a life jacket and keep loose line off the deck, where it can tangle feet.
Get new guides by emailOccasional emails. No spam. Unsubscribe anytime.